Perfecting Penreco Gel Wax: Fragrance Ratios For Success

Penreco gel wax is a high-polymer gel suitable for clear candles with medium- to high-fragrance loads. The recommended fragrance load varies from 1-7% depending on the density of the gel wax. The flash point of the fragrance oil must be 170°F (77°C) or higher to be safe for use in gel wax. This is the temperature at which the oil can vaporize and ignite when exposed to an open flame or spark. While it is possible to add fragrance to Penreco gel wax, it is not normally recommended.

Fragrance load: 1-3% for low-density gel, 5-7% for high-density gel

Penreco gel wax is a patented gel candle wax, and it is not recommended to add fragrance to it. However, if you do wish to add fragrance, it is important to ensure that the fragrance oil is compatible with gel wax. To do this, you can test whether the fragrance oil mixes well with mineral oil or baby oil without any separation or cloudiness. This indicates that the fragrance oil is non-polar and could be compatible with gel wax. However, this test is not foolproof, and it is best to refer to the manufacturer's recommendations for specific fragrance oils.

The amount of fragrance that can be added to Penreco gel wax depends on the density of the gel. For low-density gel, a fragrance load of 1-3% is recommended, while for high-density gel, a fragrance load of 5-7% is suggested. It is important to note that these percentages are just guidelines, and the specific fragrance oil used may have different recommendations.

Additionally, when working with fragrance oils, it is crucial to consider the flash point, which is the temperature at which the substance can vaporize and ignite when exposed to an open flame or spark. For fragrance oils to be safe for use in gel wax, they should have a flash point of 170°F (77°C) or higher.

Overall, while it is possible to add fragrance to Penreco gel wax, it is important to exercise caution and refer to the manufacturer's guidelines to ensure compatibility and safety.

Fragrance oils must have a flash point of 170°F (77°C) or higher

When using Penreco gel wax, it is important to ensure that any fragrance oils have a flash point of 170°F (77°C) or higher. The flash point is the temperature at which a substance can vaporise and ignite when exposed to an open flame or spark. This is a safety measure to prevent the oil from igniting during use.

To determine if a fragrance oil is compatible with gel wax, a simple test can be performed by mixing the fragrance oil with mineral oil or baby oil. If the oils mix well without any separation or cloudiness, it indicates that the fragrance oil is likely non-polar and compatible with gel wax. However, this test is not foolproof, and it is always recommended to refer to the manufacturer's guidelines for specific fragrance oils to ensure compatibility and safety.

The amount of fragrance oil that can be added to Penreco gel wax varies depending on the density of the wax and the desired fragrance load. Penreco gel wax is available in low, medium, and high densities, each with different fragrance load recommendations. For low-density gel wax, a fragrance load of 1-3% is suggested, while medium-density wax can accommodate medium- to high-fragrance loads of 0-5%. High-density gel wax has a fragrance load capacity of 5-7%.

It is important to note that adding fragrance to gel wax can be challenging, and it is generally not recommended to attempt this with gel candles. To make fragrance oils compatible with gel wax, isoparsolvents can be added to lower the polarity, but this requires significant testing. Therefore, it is advisable to follow the manufacturer's instructions and use fragrance oils specifically designed for use with gel wax to ensure optimal results and safety.

Fragrance oils can be made gel wax compatible by adding isoparsolvents to lower the polarity

The flash point of the fragrance oil is also important. The flash point is the temperature at which a substance can vaporize and ignite when exposed to an open flame or spark. For a fragrance oil to be safe for use in gel wax, it should have a flash point of 170°F (77°C) or higher.

The amount of fragrance oil that can be added to Penreco gel wax varies depending on the density of the wax. For low-density Penreco gel wax, the fragrance load is 1-3%. For high-density Penreco gel wax, the fragrance load is 5-7%. However, it is important to note that Penreco holds a patent on gel candle wax, and no company can legally sell gel wax that is not a Penreco wax. Therefore, it is recommended to refer to Penreco's guidelines for adding fragrance oils to their gel wax.

Penreco holds a patent on gel candle wax

It is important to note that fragrance oils must have a flash point of 170°F (77°C) or higher to be safe for use in gel wax. The flash point is the temperature at which a substance can vaporize and ignite when exposed to an open flame or spark. To test if a fragrance oil is compatible with gel wax, you can mix it with mineral oil or baby oil. If there is no separation or cloudiness, the fragrance oil is likely non-polar and could be used with gel wax. However, this test is not foolproof, and it is always best to refer to the manufacturer's recommendations for specific fragrance oils.

When making gel candles, it is recommended to use zinc wicks with Penreco wax as it will produce a hotter flame. Additionally, fragrance oils can be made gel wax compatible by adding isoparsolvents to lower the polarity, although this may take a significant amount of testing.

Zinc wicks are recommended for use with Penreco gel wax

Penreco gel wax is a high-polymer gel suitable for clear candles with medium- to high-fragrance loads. The fragrance load can be anywhere between 1% and 7%, depending on the density of the gel wax.

Frequently asked questions