Clean Your Ultrasonic Aroma Diffuser: Tips And Tricks

To keep your cool mist ultrasonic aroma diffuser in tip-top condition, it's important to clean it regularly. Here's a step-by-step guide on how to do it:

First, always unplug your diffuser and pour out any excess water and oil. Then, use a natural dish soap on a cotton brush to gently wipe down the reservoir, rinsing with a damp cloth to remove any soapy residue. Next, use a cotton swab dipped in rubbing alcohol to clean the ultrasonic plate or chip, which helps break down the oils. Finally, dry the reservoir with a microfiber cloth or paper towel before reassembling the diffuser. For a deeper clean, add 10 drops of distilled white vinegar to the reservoir with water, let it run for 10-15 minutes, then wipe it down and dry as before. Remember to refer to your diffuser's instruction manual for any specific cleaning guidelines, and clean your diffuser regularly to prevent oil buildup and mould or mildew growth.

Unplug and empty your diffuser before cleaning

Before you start cleaning your cool mist ultrasonic aroma diffuser, it is important to unplug it and empty any water or oil left in the reservoir. This is because, like other electronic devices, diffusers should not be plugged in during cleaning. It is also a safety hazard to keep it plugged in and running while you clean.

After unplugging the diffuser and pouring out any water or oil, you can start to clean the reservoir. Add a drop of natural dish soap to a soft, damp cloth and wipe down the entire reservoir. Then, rinse the reservoir under water to remove any soapy residue. Dry the reservoir using a dry microfiber cloth.

The next step is to clean the ultrasonic plate or chip. This is an important step because these parts work to break down essential oils, and removing any buildup can ensure that the plate continues to function properly. Use a cotton swab dipped in rubbing alcohol or white vinegar to gently rub and clear any buildup on the plate or chip.

Once you have clean diffuser parts, you can put everything back together. If desired, the diffuser is now ready for immediate use.

Clean the reservoir with a cloth and natural dish soap

To clean the reservoir of your cool-mist ultrasonic aroma diffuser, you'll need a cloth and some natural dish soap.

First, unplug your diffuser and pour out any excess water. It's important to do this from behind, to prevent water from spilling on the diffuser's operating buttons, which could cause damage.

Next, put a small amount of natural dish soap on your cloth. You want to avoid any chemical additives, as these can harm the diffuser. Gently wipe down the reservoir, removing any grime, then wipe down the outside of the diffuser, too.

Once you've cleaned away the grime, rinse the diffuser by rubbing it with a damp cloth, making sure to remove any soap residue. Keep rubbing the diffuser with a clean, dry cloth until any water running off of it is clean.

Finally, use a cotton swab dipped in rubbing alcohol to clean the mist chip, which you'll find inside the reservoir.

Clean the ultrasonic plate with a cotton swab and rubbing alcohol

To clean the ultrasonic plate with a cotton swab and rubbing alcohol, follow these steps:

Firstly, unplug your diffuser and empty any remaining water or oil. It is important to never submerge your diffuser in water, as this can damage the electronics. Instead, pour out any excess liquid. Then, take a cotton swab and dip it into some rubbing alcohol. Next, gently rub the cotton swab over the ultrasonic plate or chip to remove any excess oil build-up. The ultrasonic plate is responsible for breaking down the oils so that they can be dispersed into the air as a fine mist, so it is important to keep it clean and free of residue. Finally, allow the diffuser to air dry before reassembling.

This process can be repeated as part of a monthly deep cleaning of your diffuser, which will help to prevent mould and keep your diffuser working at its best.

Deep clean with vinegar and water once a month

To deep clean your cool-mist ultrasonic aroma diffuser with vinegar and water once a month, follow these steps:

Step 1: Unplug and empty your diffuser

Unplug your diffuser from the power source and pour out any water or oil left in the reservoir. It is important to never start cleaning your diffuser when it is still plugged in, and always dispose of any water or oil sitting in the diffuser before cleaning.

Step 2: Fill the diffuser with water and vinegar

Fill the diffuser tank halfway with clean, room-temperature tap water. Then, add approximately 10 drops of distilled white vinegar to the tank. Do not use any other type of vinegar or cleaner in the tank, as this could be dangerous. Vinegar is a great natural disinfectant that will help to break down any oils stuck inside the diffuser, as well as prevent the build-up of mould and mildew.

Step 3: Run the diffuser for 10-15 minutes

Plug the diffuser back in and let it run for 10 to 15 minutes. This will allow the vinegar and water solution to cut through and loosen any built-up oils in the tank. If you are sensitive to the smell of vinegar, you may want to place the diffuser outside or by an open window while it runs.

Step 4: Empty and wipe down the reservoir

After running the diffuser, unplug it and pour out the vinegar and water solution. Use a damp microfiber cloth to wipe down the inside of the tank, removing any lingering residues. Then, dry the reservoir with a new, dry microfiber cloth or towel.

Step 5: Clean the ultrasonic plate or chip

Dip a cotton swab in rubbing alcohol and gently wipe down the ultrasonic plate or chip to remove any oil residue. The ultrasonic plate or chip is responsible for breaking down the oils so that the water can disperse them into the air, so it is important to keep this component clean.

Step 6: Wipe down the outside of the diffuser

Use a damp microfiber cloth to wipe down the outside of the diffuser, removing any dust, debris or smudges. No soap or other detergents are needed for this step – plain water will do the trick! Just be careful not to get any water into the buttons or under the machine.

Step 7: Reassemble the diffuser

Finally, put your diffuser back together so that it is ready for use when you next need it.

Wipe down the outside of the diffuser with a damp cloth

To wipe down the outside of your cool mist ultrasonic aroma diffuser, you'll want to use a damp cloth.

First, make sure your diffuser is unplugged and there is no water or oil left in the reservoir. Then, dampen a cloth with clean water and wipe down the outside of the diffuser, taking care not to get any water into the buttons or under the machine.

If there are any smudges or fingerprints on the diffuser, a damp cloth will help to remove them. You can also use a soft brush or toothbrush to remove any excess oil. It's important to only use natural cleaners without any chemical additives, as harsh chemicals can damage the diffuser.

In addition to wiping down the outside of the diffuser, you should also clean the inside of the reservoir and the ultrasonic plate or chip. This will help to remove any oil buildup and prevent corrosion. You can use a cotton swab dipped in rubbing alcohol or white vinegar to gently wipe down these components.

By regularly cleaning your diffuser, you can prevent mold and residue buildup and ensure that it continues to function properly.

Frequently asked questions